• Hello there guest and Welcome to Modular Fox Mustangs home of the 2V, 3V, 4V, Coyote Modular Mustang Conversion Information Website!
    To gain full access you must Register. Registration is free and it takes only a few moments to complete.
    Already a member? Login here then!

07 gt 4.6 3v into a 93 coupe

rcustomz

Active Member
about 95% done, just need a few more things and i'll be driving it. Starts and runs great.. i used the full 07 gt harness and cluster, just trying to make everything look like it belongs. Headlights work, and sequential tail lights .. i used gt tail lights.
 

Attachments

  • 20160405_213113.jpg
    20160405_213113.jpg
    127.5 KB · Views: 93
  • 20160326_130932.jpg
    20160326_130932.jpg
    147.2 KB · Views: 67

rcustomz

Active Member
i used the 07 gt trans, along with the harness and it had a hurst short throw. so i moved it back to fit right.
 

Bignate76

Member
Does the 07 GT transmission have different shifter plates so you can move the shifter wherever you want or did you have to move the engine on the Cradle to get it to move back to where you want it?
 

rcustomz

Active Member
Does the 07 GT transmission have different shifter plates so you can move the shifter wherever you want or did you have to move the engine on the Cradle to get it to move back to where you want it?
the 07 gt trans has the remote shifter, it has linkage that sets it back a few inches. i had to cut the tunnel a little bit for it to fit
 

rcustomz

Active Member
It's official done, just have the A/C left but i've been driving it... and it was at MW 2016
 

Attachments

  • 20160706_193834.jpg
    20160706_193834.jpg
    3.9 MB · Views: 91
  • 20160706_193858.jpg
    20160706_193858.jpg
    3.8 MB · Views: 55
  • 20160706_194053.jpg
    20160706_194053.jpg
    3.9 MB · Views: 69
  • 20160722_075206.jpg
    20160722_075206.jpg
    6.1 MB · Views: 60
  • 20160722_080441.jpg
    20160722_080441.jpg
    6.7 MB · Views: 63
  • 20160729_131730.jpg
    20160729_131730.jpg
    6.3 MB · Views: 71
  • 20160729_131744.jpg
    20160729_131744.jpg
    6.3 MB · Views: 71
  • 20160729_131812.jpg
    20160729_131812.jpg
    5.4 MB · Views: 92
  • 20160729_131820.jpg
    20160729_131820.jpg
    4.9 MB · Views: 62

cobfa9646

Member
I used stock headers with the adapters...I was trying to use a stock k member. I'm having to modify the hpipeit is to tight. I ended using a tubular km ember anyways. If I did it again I would use full length headers.
 

Alex

Member
I used stock headers with the adapters...I was trying to use a stock k member. I'm having to modify the hpipeit is to tight. I ended using a tubular km ember anyways. If I did it again I would use full length headers.


Thanks. I am using a Team Z k member. Just working on other things first haven't tried to fit the engine yet.
 

Lukepritchett18

New Member
I know this is an older thread but how much trouble was it wiring the Fox dash to the s197 harness? Also what’d you do for your fuel system as far fuel pump?
 

Bill

Well-Known Member
Staff member
Donator
Hi Luke, welcome to the party. I don't do much wiring, but I'm hopeful that someone will get back to you soon.
 
Top